Home › Leaking Tap and Mixer Repairs in Clayton

Taps and mixers · Clayton VIC 3168

Leaking Tap and Mixer Repairs in Clayton

A dripping tap wastes water and usually gets worse. We repair and replace kitchen, bathroom, laundry and outdoor taps across Clayton, from 1960s spindle taps to modern mixers. Call 03 9088 4192.

Plumber replacing the cartridge in a basin mixer tap in a tiled 1970s bathroom, old parts on a towel
Call a Clayton plumber03 9088 4192Licensed · local · price agreed first
Licensed and insured Clayton 3168 based After-hours help

Common tap problems

  • Taps that keep dripping after being turned off
  • Water leaking from the base of the tap or around the handle
  • Mixer taps that are stiff, wobbly or hard to adjust
  • Taps that make a squealing or hammering noise
  • Low flow from one tap only
  • Outdoor taps leaking at the wall or the handle

Two-handle spindle taps

Many older Clayton homes still have separate hot and cold taps with a spindle and a rubber or fibre washer inside. When the washer wears, water seeps past it and the tap drips. Rewashering is usually a quick repair. If the seat the washer sits on is worn or pitted, we reface it so the new washer seals properly. Without reseating, a new washer may only last a few weeks.

Leaks around the handle usually mean the o-rings on the spindle have worn out. We replace them while the tap is apart.

Mixer taps

Single-lever mixers use a ceramic cartridge to control both flow and temperature. Over time the internal seals wear and the cartridge starts to drip or becomes stiff. Hard water and debris from older pipes can speed up this wear. In most cases we replace the cartridge with a genuine or compatible part. If the tap body is damaged or the model is no longer supported, replacing the whole mixer may be better value.

Outdoor taps

Garden taps take a beating from weather, hose fittings and being turned too hard. We repair leaking garden taps, replace broken ones and fit vacuum breakers where required to protect the drinking water supply from backflow.

New tapware

If you are updating a kitchen or bathroom, or your old taps are beyond repair, we install new tapware. We make sure new taps carry WaterMark certification as required in Australia, check they suit your water pressure, and fit them with new isolation valves and flexible hoses where needed.

Why fix a dripping tap?

A tap that drips steadily can waste thousands of litres of water a year. On a hot tap, you are also paying to heat that water. Drips also stain basins and sinks, and they nearly always get worse.

Taps in rentals

Dripping taps are a common item on rental maintenance lists. We work with agents and landlords to fix taps across a property in one visit, and we check for other small issues like running toilets and slow drains while we are there.

Water pressure and taps

High water pressure wears tap washers and cartridges faster. If several taps in your home are dripping, or one keeps failing after repairs, we can test the pressure and fit a pressure limiting valve if needed.

How we work

We assess the tap, explain whether a repair or replacement makes sense and agree the price before starting. We carry common washers, o-rings, seats and cartridges in the van so most repairs are done on the spot. When we finish, we check the tap runs smoothly and shuts off cleanly.

Laundry and washing machine taps

Laundry taps are often the forgotten ones. Washing machine taps left on all the time put constant pressure on the hoses, and a hose failure can flood a laundry quickly. We replace worn washing machine taps with quarter-turn models that are easy to turn off when you go away, and check the hoses at the same time.

Kitchen mixers with pull-out sprays

Pull-out and pull-down kitchen mixers are popular, but their flexible hoses and spray heads can wear and leak under the sink. If you find a damp cupboard base, the hose or its connection may be the culprit. We can replace the hose or the whole mixer if parts are not available.

Squealing and shuddering taps

A tap that squeals or makes the pipes shudder when turned usually has a loose washer or worn jumper valve inside. Replacing the washer and jumper usually fixes it quickly.

Included

What comes with every tap and mixer repairs job

DiagnosisWhichever test tool suits the fault, and you see the result for yourself
PriceSettled face to face before we start, and confirmed in writing on bigger work
Who does itA Victorian-licensed, insured plumber, never an unqualified offsider
PartsWaterMark-approved materials fitted to the plumbing code
RecordsA Victorian compliance certificate where the law calls for one, and photos on request
FinishRun and checked in front of you, then swept up and cleared away

Questions

Tap and Mixer Repairs in Clayton: your questions

Is it worth fixing an old tap or should I replace it?

Many older taps are worth repairing with a new washer and reseated seat. If the body is corroded or parts are no longer available, a new tap may be better value.

Why does my tap still drip after a new washer?

Usually because the seat is worn or pitted. We reface the seat so the new washer can seal properly.

Can you fix my mixer tap or does it need replacing?

Most mixers can be repaired by replacing the cartridge. If the body is damaged or parts are unavailable, we will recommend a replacement.

Do new taps need to be certified?

Yes. Tapware installed in Australia must carry WaterMark certification.

Can you fix all the taps in my rental at once?

Yes. We can work through all the taps in a property in one visit and send a report to the agent or landlord.

Can you replace a tap the same day?

Usually yes. We carry common tapware and parts, and if you have chosen a specific model we can fit it once it arrives.

Why is my outdoor tap leaking at the wall?

Usually a worn washer, a loose fitting or a cracked tap body. We repair or replace it and check the connection behind the wall for leaks.

Book or get a quote

Tell us about the job

Fill in the basics and a licensed Clayton plumber will ring you back. If water is escaping right now, skip the form and phone 03 9088 4192.

03 9088 4192

Prices are never listed online. We inspect first, then settle the cost with you before a single tool comes out.







    How a job runs

    From the first call to the final check

    1. 1Call or send the form

      Tell us what is going on and what kind of place it is. Snap a picture of the leak, the drain or the sticker on your cylinder and send it through, so the right spares come with us.

    2. 2We find the cause

      On site we track down the fault, show you what we found and agree the price with you. No work starts until you are happy.

    3. 3We fix and test it

      Repairs are done to the Plumbing Code of Australia and the relevant standards, then run and checked with you there.

    4. 4Clean up and paperwork

      Old parts go in the van, the area is left tidy, and you get a written summary plus a compliance certificate where one is required.

    Where we work

    Clayton first, then the suburbs either side of it

    Most days begin within a few streets of Clayton Road. From there it is a short run up to Notting Hill and Mount Waverley past the university, west along Centre Road to Oakleigh, Huntingdale and Oakleigh South, south over Heatherton Road into Clayton South, and east along Wellington Road and the Princes Highway to Mulgrave and Springvale. Somewhere else nearby? Ring 03 9088 4192 and we will tell you honestly if we can get there.

    Plumbing problem in Clayton? Talk to the plumber who will fix it.